Edition GB – T05REMKO SVSV 261, SV 351, SV 521, SV 681Ceiling-mounted split design air conditioning unit Operation · Technology · Spare parts
Mode DRYPress the MODE button once or repeatedly to switch to dehumidifying mode. Use this mode to dehumidify the room in an unregulated fashion. Afte
The NETWORK button has not been as-signed a function.NETWORK ButtonSLEEP ButtonMode HEATPress the MODE button once or repeatedly to switch to heating
TIME ButtonsSwitch-on timeSwitch-off timeThe TIME-ON/-OFF buttons are used to program the switch-on/off time, the TIME-SET button to set the time.Pres
ShutdownTemporary shutdown1. Let the indoor unit run for 2 to 3 hours in circulation mode, or in cooling mode at maximum temperature, to extract any
Cleaning the condensation pumpThe indoor unit includes a built-in condensation pump for pumping the condensation to a drain at a higher level.The pump
Troubleshooting and customer serviceThe equipment and components are manufactured using state-of-the-art production methods and tested several times t
Error indicated by flashing codeH (Red)M (Yellow)L (Green)Cause Required actionon Fan at max. speed Normal operating conditionon Fan at medium speed No
Installation instructions for qualified personnel Transport the unit in its original packaging as close as possible to the installation location.This
Installation materialThe indoor unit is fastened using 4 threaded rods (provided by the customer).In order to complete the installation, wall plugs, t
Warm airFresh cold airLight wellOutdoor componentWarm airLight wellAdditional fan 5 Installation inside buildingsInstallation inside buildings
InstallationInstalling the unitThe indoor unit is mounted face down on four threaded rods. Take into account the ceiling grid and any other installati
2. Remove the factory-fitted protective caps and union nuts on the connections. These should be used during installation.3. Before flanging the refrig
It is only permitted to connect one fresh air intake and one adjacent room! CAUTION2. Carefully remove the insulation behind the opening (Fig 9)
Connection to adjacent roommax. 7 mAdjacent roomMain roomCondensation connectionIf the temperature falls below the dew point, condensation will f
16-20 mmmin. 2% fallRiser pipe too far away Condensation pipe too large/smallNo fallCannot freely drain awayCondensation connection - Wrong! Condensat
Jp6SM1 SM2 SM3 SM4MFFLHFJp12MTJP1M1Jp 3NVLCEcFOPLOHPHPLPJp11OPTJp9 Jp10 Jp7 Jp8Jp141JPJp3Jp5FJpJpCJp4REH RELAUX EC CPUConnecting the outdoor compon
Before commissioningAfter the tightness check has been successfully completed, connect the vacuum pump via the pressure gauge station to the valve con
Functional checks and test runCheck the following points: Tightness of the refrigerant pipes. Compressor and fan running smoothly. In cooling mode,
Unit dimensions All values in mmSV 261 AT to SV 521 ATSV 261 IT to SV 681 IT65065028065028580780510280250540SV 681 AT285615500315845258150185207100298
Exploded view SV 261 IT to SV 681 ITSpare parts list7123456689101112131415161718We reserve the right to modify the dimensions and constructional desig
Carefully read this operating manual prior to commissioning or using the equipment!This manual is an integral part of the unit and must be stored at t
Exploded view SV 261 AT to SV 681 ATSpare parts listWhen ordering spare parts, please state the computerised part no., unit number and type (see ident
Technical dataSeries SV 261 SV 351 SV 521 SV 681Operating modeCeiling cassette wall-mounted air-conditioning units for combined cooling/heatingNomina
Subject to technical modifications, no responsibility taken for the correctness of information!ConsultancyIntensive training means our consultants are
Safety notesDisposal of packagingAll products are carefully packaged using environmentally friendly materials prior to transportation. Make a valuable
The equipment was shipped in sturdy packaging. Immediately check the equipment on delivery and make a note of any damage or missing parts on the deliv
Infrared remote controlThe infrared remote control can send the programmed settings from a distance of 6 m to the receiver on the indoor unit. Data wi
Buttons on the remote control Button "POWER" Press this button to start the unit. Button "TEMP" Press this button to set the d
A symbol is shown on the display to indicate that the settings are being transferred.Button functionsPOWER ButtonPress the POWER button to activate/de
MODE ButtonPress the MODE button once or repeatedly to switch to automatic mode. In this mode, the regulation automatically selects COOL or HEAT mode
Kommentare zu diesen Handbüchern